1. The major difference between concrete block and clay brick is compressive strength. Compressive strength is the property of any material to with stand pressure. Going by the materials clay bricks and concrete bricks are made, the concrete bricks have much more compressive strength. 2. The second difference is water resistance. Concrete bricks have more water resistance and don't absorb water, this makes them almost waterproof and is always beneficial for construction activities. 3. The shelf life of concrete is lesser than those of clay bricks. Concrete works good for around 60 to 100 years, while clay bricks have been known to last for 1000 years and more. 4. Concrete blocks are not environmental friendly, while clay bricks are made up of natural resources, and other than the baking of bricks, everything is fine with the environment. 5. Finally, as an architect, there is beauty in clay bricks and strength in concrete bricks.

A concrete plant, also known as a batch plant or batching plant or a concrete batching plant, is equipment that combines various ingredients to form concrete. Some of these inputs include water, air, admixtures, sand, aggregate (rocks, gravel, etc.), fly ash, silica fume, slag, and cement. There are two main types of concrete plants: Dry mix plants and Wet mix plants, and also plants that contain both a transit mix side and a central mix side while utilizing common material storage points. A concrete plant can have a variety of parts and accessories, including: mixers (either tilt drum or horizontal or in some cases both), cement batchers, aggregate batchers, conveyors, radial stackers, aggregate bins, cement bins, heaters, chillers, cement silos, batch plant controls, and dust collectors. The heart of the concrete batching plant is the mixer, and there are many types of mixers such as Tilt Drum, Pan, Planetary, Single Shaft and Twin shaft mixer. The twin shaft mixer can ensure an even...

Pakistan, the good neighbor of China, a large population in South Asia, A mysterious and vibrant land,  in recent years, with the support of the "one belt and one way" China policy, all aspects of social and economic development have been greatly developed, especially in terms of infrastructure. Achievements, take this opportunity, in the field of construction machinery at home and abroad has more than a well-known professional producer: Quanzhou city Sanlian Machinery Manufacture Co., Ltd., is fully prepared, continuously improve and optimize marketing channels, the company's three major advantages: fully automatic concrete block making machine, concrete batching plant, EPS sandwich wall panel production line has brought this new hot soil. Considering it is an important new market for the company, S.L Machinery has participated in BUILD ASIA Exhibition in Karachi, the largest city, starting with professional construction exhibitions. We met a large number of Pakistani domestic bu...

With the coming of industrial 4.0 era, the market share will gradually squeeze out a considerable part of the small and medium-sized unburned block machine market. After a considerable period of development, it will eventually become the protagonist in the unburned brick machine market. The introduction of the national supply-side reform will gradually balance the supply-demand relationship of the original large-scale unburned brick machine equipment market. But nowadays, there are only a few manufacturers in the market of large-scale unburned brick machines in China who can really meet the international advanced level. Quanzhou Sanlian Machinery is the leading enterprise in the top level of manufacturing large-scale non-fired brick machine equipment in China. It can provide full-automatic high-end production line complete sets of equipment with annual output of 30-1 million square meters of permeable bricks and 50-200,000 cubic meters of blocks, and the implementation plan of the cons...

Foam concrete block is foamed by the foaming machine. The foam agent is fully foamed by mechanical way , and the bubles mixed with cement evenly, then injected into the mold, forming a new lightweight thermal insulation material which contains a large number of closed pores. It is a bubble like insulation material, which is characterized by the formation of closed foam holes so that the foam concrete blocks are lightweight and heat-insulation. Main raw materials: cement, fly ash, fiber, foam agent, and additives. These raw materials are mainly inorganic. There are no harmful substances and no odor. No decomposition in the application process, which is green and environmentally. The foaming agent is neutral and without harmful substances such as benzene and formaldehyde, it avoid environmental pollution and potential fire hazards. It is the best choice for the insulation building. The process of production Material weighing - material mixing (adding foam agent, additives, etc.) - materi...

How to maintain permeable brick making machine 4 Important advice You deserve to learn from 27-years -experience expert 1. High attention on brick making machine mold ① Clean up the mold cavity, get rid of the oil and dirt on the surface. Spray anti-rust oil onto mould cavity. ② Check whether the relevant parts of the brick making machine mold are damaged, and fasten the loosen parts to ensure the safety and reliability of the brick making machine while producing; ③ Check whether the extruding, forming and pressing surface of the brick making machine mold are worn, repair it by welding, grinding, and polishing. ④ Check the blanking and blanking parts, repair and replace the damaged parts; check the guide and the wedge mechanism to repair and replace the worn and cracked parts. 2.     Accurate oil temperature adjustment of permeable brick making machine Start the hydraulic system water and wind cooler beforehand esp in winter. When the oil temperature exceeds 45 degr...

Introduction on raw material of lightweight EPS wall panel     Since ancient times masonry walls are the main component in the housing sector and it has brittle characteristics and exhibit poor performance against the uncertain loads. Further, the structure requires heavier sections for carrying the dead weight of masonry walls. S.L Machinery develops a simple, lightweight and cost effective technology for replacing the existing wall systems. The lightweight concrete is developed for the construction of sandwich wall panel. The EPS beads of 4-6 mm diameter size are mixed with cement concrete and developed a lightweight concrete with a density 9 kN/m³. Sandwich wall panel is composed of cement, fly ash, EPS (expanded polystyrene foam particles), foam agent and additives (such as hydroxymethyl cellulose, reusable dispersion emulsion powder, water reducing agent etc.), mixing with water according to certain proportion, then grouting and forming. The lightweight sandwich pan...

DURING THE INDUSTRIAL REVOLUTION of the 18th and 19th centuries, the basic materials of construction were sparse. There was wood, stone, brick and mortar, and iron and steel. However, the irons and steels of that day were vastly inferior to the ones used today. With the progress of human civilization and the pursuit of a better quality life, today S.L Machinery perfectly combined the technology of Lightweight wall panel material and steel structure by launching the lightweight concrete wall panel making machine.     Lightweight concrete is now an established lightweight building material. It is used not only on account of its light weight but also because of high thermal insulation compared with normal concrete. The lighter the concrete, the larger the insulation properties in general. An earliest application of lightweight concrete was in building industry and for producing insulating screeds. The principal structural use of lightweight concrete is in construction of under b...

Introduction on Light Weight Foam concrete Plant The light weight foam concrete block is a kind of foaming agent that is fully foamed mechanically through the foaming system of the foaming machine, and the foam is uniformly mixed with the cement slurry, and then injected into the mold to be formed. It is formed by natural curing, a new type of lightweight thermal insulation material with a large number of closed pores. It is a bubble-shaped heat-insulating material, and its outstanding feature is that the closed foam cells are formed inside the concrete, so that the foamed concrete block can achieve the effect of light weight and thermal insulation.    The light weight foam concrete is prepared by directly adding hydrolyzed natural resin foaming agent to cement concrete or prefabricating a large amount of foam without adding perlite, polypropylene EPS beads and other materials. The main feature of this kind of foam is that its water absorption rate is less than 5%, no connect...

HZS 35 concrete mixing plant is the most cost-effective concrete mixing plant thus a lot of customers are interested in, we will make a brief introduction on HZS 35 concrete mixing plant. 1. Product type and scope of application The main machine of this model is a double horizontal shaft forced concrete mixer. Designed and manufactured according to GB/T9142-2000 concrete mixer. It is applicable to all kinds of small and medium-sized prefabricated component factories, highway and bridge, water conservancy, wharf and other industrial and civil construction engineering construction departments, and can mix dry and hard concrete, plastic concrete, mobile concrete, light aggregate concrete and various mortar. This model is equipped with PL1600 series batching machine and 100t flake powder tank (refer to the powder tank installation instructions and videos). 2. Main technical parameters of HZS35 1) Mixing part： Host model： JS750 Mixer Charging volume： 1200L Discharging volume： 750L Rate...